Видео

Yeah, thanks for this video. Way simpler method than scarfing ply! And there is no appreciable loss of strength.

Are you high? 😂 great video anyway

Thanks for the video, this is something that is usually glossed over in most builds, also the first time I've heard of peel ply. Also, did not realize you can do this without a backing block!!

Here’s a cookie for nothing🍪

Did you kill the crab ?🦀 or was it dead already?

This is a good tutorial. The part about using heat to drive out the water and flow in the adhesive seems critical. I personally am going to try JB Weld Plastic Bonder (2 part polyurethane...). It is basically "panel bond" as I understand it, and Plastic Bonder claims to be flexible (makes sense if it is truly polyurethane), which is what I really need to repair the leaky seam in the bow of my aluminum starcraft boat. That part of the boa takes a beating and previous repair (epoxy I think)...has cracked and is leaking. Wish me luck.

What would you suggest to adhere to acrylic? More specifically Seadoo jet ski cm-tec hull repair?

Can you guys reupload this without the music?

i think you'll fond that half of 100 is 50..? not 44..??

You forgot the most important part the mask for safety.

I recently did a project for my daughter and the box said it was a 1 to 1 ratio but it still came out sticky even after 3 months so I must have done something wrong

Question. My Peel ply will not come off like yours, any idea why? Epoxy resin +glass. I had a final layer of parchemin paper before placing wood and weight on top. Should I fight to get the Peel ply off or can it stay on? Thank you for a well done video.

This is a evet primitive approach for seams. I am udine zipper like shapes to increase binding area and scatter momentum along the seam.

Is there a way to make a left side part from right side part? (example, a left side panel into a right panel)

What is peel ply? Is it a type of fiberglass? Does it stay there permanently? What is its purpose?

video about sand paper

I have spent so much time reading what you just said and nothing was clicking. Today I was an audible learner. Thank you for making that so easy.

Annoying music. No need but thanks for video

Wow, the photographer stuck to him like glue to get fantastic closeups during the whole wetting out process. BTW, from 10:37 - 10:40 I seem to see a lot of wet "stringies" hanging down from the rail and I'm surprised he doesn't cut those off. Surely he's not going to lap them around to the deck. They always cause so much trouble when glassing the deck. OK, so I watched some more, and he lays them down parallel to the rail and not out onto the deck. BTW, photography at 13:28 is incredible; you can see the drips so clearly! Kudos to the cameraman!

Hi! Just wondering how you’d recommend fixing a Jamie SLS with damage into the wood core?

Nice process

Finally a person that explains it !! Thank you so much. Thumbs up and a like! And a follow !

Thanks for sharing your videos....can I fiberglass around/over hardware cloth?

Hes high on glue 😅😂

Hi I have a triangle that I would like to use epoxy for. The triangle size is 50 cm x 50 cm x 50 cm. First time doing this how much show I use? Thank u for ur videos

If I chip brushed then rolled and then used a bubble busting roller could i use this method on 1708 without priming board with resin first. When i say board i mean a piece of lumber. Thanks for the videos!

leaving in the fail is the mark of true professionals, excellent work, I'm thinking of making moulds for 1964 Triumph 650 thunderbird half skirts, I have original steel ones, but they are really rare to find.

Thank you ❤

Just getting the roids right and you're good to go 🎉.

Hmm got a question. Got some plans for a 20 foot Jon boat. It says it needs a butt and bulkhead every 4 feet. So this is the butt joint and then you use plywood and hardwood laminated together with epoxy and fiberglass atop this butt joint?

Some epoxies create bubbles while mixing them and these bubbles tend to mar the output of the job. What do I do to ensure that these bubbles do not come up? Thanks

What kind of resin do you use?

Great video. If you were to use fibreglass for the actual part. How would the method differ to this? As you did a carbon outcome and ill be doing a fibreglass outcome. Thanks

I thought about trying to replicate fenders for 1973-1987 Chevy dual rear wheel trucks. They are large compared to your demonstration and with many complex angles. Would I need to make a split mold to get the part out?

You da Man !!!

Nice lecture thankyou

great tutorial - I need this, thanks!

I make custom kids pedal planes. A few years ago I started to do them in fiberglass. Needless to say I have been online a lot digging into the procesess of making a mold. YOUR video is the quickest one I have seen that just gets to the point. Thanks for this video. I have saved it for future reference.

How did he have so much time? 9 minutes working with the same resin without it hardening?

What is he dabbing on the fiberglass, yall never explained that bit

any recommendations on how to fix a core shot in the bottom of a carbon TT board that goes into the wood (Jaime SLS)? a layer of fiberglass and epoxy like this?

Can you "keep" epoxy once mixed? Is there a way to prolong it's life while coating in case the area being coated takes longer than the advertised 1 hour?

Super cool!

Also, it's not necessary to mask of your tracks?

What cutting tip did you use for cutting your tracks out?

Sar very good jobs thanks 👌👌🙏🙏

Can this be done with polyester resin? If so, any alteration in the process? Thanl you for the video very informative

Is it okay to skip the surface agent and just paint directly onto the tacky surface? I’m building a teardrop trailer and plan on painting with a bed liner. Could that go directly onto the polyester resin?

You have a link to where and ehat materials i need

The big gap looks like shit.